Plume - where a release into the air goes
The Plume layer answers two questions about anything released into the air: where does it go now, and who has been under it, how much and how often, over a year. It draws the answer as contour bands around the sources and writes the result onto the buildings, schools or homes you name, so they can be colored, filtered and charted like any other data.
It has no data source of its own. The sources are features on other layers of the map, and the weather comes from the same weather model the Weather and Flow particles layers read.
Sources
Add the things that release something as ordinary layers first, then name them under Sources. Each set of sources is one layer and one family:
- Stacks and vents. The layer's points. Each has a height and exit conditions (diameter, velocity, temperature), which lift a warm plume above the stack before the wind carries it. A single stack can also be entered by its position, with no layer behind it.
- Roads and other lines. The layer's lines. The emission is spread along them.
- Open areas. The layer's polygons: a tank, a lagoon, a landfill cell, a stockyard. The emission is spread over them.
For each parameter, pick the column that holds it and the value to use where a row is empty. With no column chosen, every source in the set takes the value you enter. For lines and areas, say whether the emission rate is for the whole feature, per meter of line or per square meter.
What is released
Choose a substance to set the units, the default contour levels and the default long-run statistic.
| Substance | Emission | Read in | Default levels | Long-run statistic |
|---|---|---|---|---|
| Any release | g/s | µg/m³ | 1, 10, 100, 1000 | mean |
| Nitrogen dioxide | g/s | µg/m³ | 10, 40, 200 | mean |
| Particles (PM10) | g/s | µg/m³ | 10, 40, 50 | mean |
| Fine particles (PM2.5) | g/s | µg/m³ | 5, 10, 20 | mean |
| Sulfur dioxide | g/s | µg/m³ | 20, 125, 350 | 99.7th percentile |
| Odor | ouE/s | ouE/m³ | 1.5, 3, 6 | 98th percentile |
The levels are screening defaults drawn from published limit and benchmark values. Enter your own under Contour levels when your assessment uses others.
The weather now
By default the layer reads the wind and the cloud over the sources from the weather model, and works out how readily the air is mixing from the wind, the height of the sun and the cloud. A hot, still afternoon mixes a plume upward quickly; a clear, still night keeps it narrow and carries it a long way.
Turn Use the live weather off to ask "what if": set the wind speed, the direction it blows from, and the stability of the air yourself.
Long-run exposure
Turn on Solve over a weather record and pick a period. The layer then runs the same model over every hour of that period's real weather and rolls it up. Choose what the surface shows:
- Mean over the hours. The number an annual limit is compared with.
- Percentile of the hours. The level passed in a small share of the hours. Odor benchmarks are written this way: the 98th percentile is the level passed in 2 % of the hours.
- Hours above a level.
- Worst hour.
- Hours downwind. How often the place is in the plume at all, whatever the amount.
Under Hours of the day that count, Days that count and Months left out you can restrict the question to the hours someone is there: a school day in term time, a night shift, summer weekends.
The weather record
The record is the weather model's own analyses for the site of the sources: the regional wind in cells of about 100 km, four times a day, from January 2022, for up to two years. Reading a year takes a couple of minutes. It is read once, while the layer's pane is open in the editor, and then kept with the map, so the map gives the same answer every time it opens and a published map's readers fetch nothing.
Because the cells are large, the record is the wind of the region, not of one valley or one street. Where local winds differ sharply from the regional wind, treat the long-run surface with that in mind.
Particles
While the map shows the weather now, particles leave the sources and drift with the wind over the contour bands, spreading as the bands do and colored by their own level. When the weather changes, the change travels down the plume. Under Look you can turn them off, choose how many there are, color them by the source they left, and set their speed, opacity and size. They are never shown to readers who prefer reduced motion.
Compare with a scenario
Under Compare with a scenario, add a second set of sources: the same layers with other values (a taller stack, a covered tank, half the traffic) or other layers. Copy the sources above gives you a starting point. The layer then shows the sources above, the scenario, or the difference, the scenario minus the sources above, in blues where there is less and reds where there is more. Bookmarks can switch between them, so a before, an after and a difference can sit on three pages of one map.
A fire or a leak
For a release that began at a known time, set the source's family to A fire or a leak and fill in When it happened: when it began, when it stopped (leave that empty while it is still going) and how many hours to follow it. The layer then carries the release on the wind as it was and as it is forecast, hour by hour, and takes its place on the map's time slider: play it to watch the plume grow, swing with the wind and clear after the release stops. The highest level it reaches shows everything the plume passes over in one picture.
Each receiver gets plPeak, the highest level it sees, and plArrivalH, the hours from now until the plume first arrives (negative when it already has), so a table of schools or care homes can be sorted by who is reached first.
A layer with a fire or a leak shows only those sources. Put chimneys, roads and areas on a Plume layer of their own. The wind is the regional wind for the whole area at each hour, and the ground is taken as flat.
A volcanic eruption
Set the source's family to A volcanic eruption and give it the vent: a layer with the volcano as a point, or its position. Under The eruption, enter when the emission began and stopped and the height the column reached, from the observatory's bulletin or the volcanic ash advisory. The layer then carries the ash on the weather model's wind at every level up to about 16 km, lets it settle by grain size, and puts the result on the time slider.
- The ash cloud is drawn at the time slider's moment, as the concentration within a band of flight levels: surface to FL200, FL200 to FL350, above FL350, or the worst of the three. The default levels, 0.2, 2 and 4 mg/m³, are the low, medium and high contamination thresholds aviation uses.
- The ashfall on the ground is drawn in g/m², by default at 1, 10 and 100: a trace, visibly covered, disruptive.
Add airports or towns as receivers and each gets plArrivalH, plPeak and plDeposit, its ashfall.
The mass released is estimated from the height of the column, which it grows steeply with, so use the height the advisory uses. This is model wind, not satellite observation, on flat ground with no rain washing ash out. It is for awareness and explanation, and it is never a substitute for the official volcanic ash advisory.
Receivers
Under Receivers, add the layers to score. Each feature gets its own values, at its center:
| Value | Meaning |
|---|---|
plConc |
The level now |
plBand |
Which contour band it is in now |
plTopSource |
The source that contributes most now |
plExp |
The long-run value |
plExpBand |
Which band of the long-run surface it is in |
plHours |
Hours downwind over the record |
plDelta |
The change, scenario minus the sources above, while the difference is shown |
plPeak |
A fire, a leak or an eruption: the highest level over the whole period |
plArrivalH |
A fire, a leak or an eruption: hours from now until it first arrives |
plDeposit |
An eruption: the ashfall, g/m² |
With Color the features by their band on, they take the surface's colors. The Last solve section lists the area inside each contour and what the model did, including how many calm hours it left out.
What the model is
A steady-state Gaussian plume, the screening method air quality practice has used for decades: Pasquill stability classes with Briggs spread curves for open country or built-up ground, Briggs plume rise for stacks, reflection at the ground and at the mixing height, and a simple correction where the ground rises toward a receptor. It is valid to roughly 20 km from the sources, and the extent is limited to 60 km across.
Read every result with these limits in mind:
- It is the contribution of the sources on the map, not the concentration in the air. There is no background level, no chemistry, no deposition and no effect of buildings on the flow.
- Calm hours are left out. The method has no meaning in still air, so hours below about a meter a second of wind are excluded from the long-run surface and counted in the report.
- An odor result is only as good as the emission rates entered. With the default rates the map shows how often a place is downwind, not how strong the smell is.
- It is a screening estimate for comparing, prioritizing and explaining. It is not a substitute for a regulatory dispersion model, and it is not for permitting or compliance.
Availability
The Plume layer is part of the Planning pack. It is an Icon Map for Fabric layer; the Power BI visuals do not have it.